Browsing by Author "Pereira, Carlos M."
Now showing 1 - 5 of 5
Results Per Page
Sort Options
- Electrochemistry-assisted surface plasmon resonance detection of miRNA-145 at femtomolar levelPublication . Ribeiro, José A.; Sales, Maria Goreti Ferreira; Pereira, Carlos M.In this work, we combined electrochemical techniques with SPR (eSPR) for the label-free detection of cancer biomarker miRNA-145. Detection was performed in a simple two-step assay. In the first step, the gold sensor surface, previously functionalized with a self-assembled monolayer (SAM) of thiolated RNA probes is incubated with the sample containing the target RNA biomarker. In this step, hybridization of RNA fragments with complementary immobilized probes was monitored in real-time by SPR. In the second step, eSPR measurements were performed to improve the sensitivity of the hybridization assay. Potential-induced deposition of a redox probe at the sensor surface resulted in enhanced SPR response promoted by the electrochemical process, thereby allowing the detection of miRNA-145 at femtomolar level (LOD = 0.56 fM), without sample derivatization or post-hybridization treatment for signal amplification. Good linearity was achieved (R2 = 0.984) over the concentration range from 1.0 fM and 10 nM. Furthermore, the developed eSPR biosensor showed high selectivity towards single-base and two-base mismatch sequences and detection of target miRNA-145 in synthetic human serum was successful achieved.
- Protein Imprinted Material electrochemical sensor for determination of Annexin A3 in biological samplesPublication . Rebelo, Tânia S.C.R.; Pereira, Carlos M.; Sales, Goreti; Noronha, João P.; Silva, FernandoThe development of fast and reliable methods for protein determination are of great relevance to a diversity of areas from industry to diagnostics. Molecular Imprinted Materials (MIM) has proved to be an interesting methodology for protein analysis however further studies of the effect of the experimental parameters and starting materials in the performance of the MIM are still required. Caffeic acid (CAF) is employed for the first time as a monomer to tailor a synthetic receptor for a protein target. This was done by bulk-electropolymerization, applying a constant potential of +2.0 V, for 30 s, on a carbon screen- printed electrode, immersed in a solution of protein and CAF prepared in phosphate buffer. Annexin A3 (ANXA3) was selected as protein target due to the fact that this is an emerging biomarker in prostate cancer. The assembly of the protein imprinted material (PIM) was followed by Electrochemical Impedance Spectroscopy (EIS) and Raman Spectroscopy. A non-imprinted material (NIM) was prepared in parallel as control. Square wave voltammetry (SWV) was used to monitor the electrochemical signal of the [Fe(CN)6]3 /[Fe (CN)6]4 redox for the quantification of ANXA3. The optimized PIM-based device showed average detection limits (LOD) of 0.095 ng/mL, a linear behavior against log (concentration) between 0.10, and 200 ng/mL and good selectivity. The NIM-based device showed random behavior against protein concentration. Finally, the PIM-sensor was successfully applied to the analysis of ANXA3 in spiked urine samples.
- Protein imprinted materials designed with charged binding sites on screen-printed electrode for microseminoprotein-beta determination in biological samplesPublication . Rebelo, Tânia S.C.R.; Pereira, Carlos M.; Sales, Goreti; Noronha, J.P.; Silva, FernandoIn the past few years a large effort is being made aiming at the development of fast and reliable tests for cancer biomarkers. Protein imprinted sensors can be a fast and reliable strategy to develop tailor made sensors for a large number of relevant molecules. This work aims to produce, optimize and use in biological samples a biosensor for microseminoprotein-beta (MSMB). Caffeic acid (CAF) electropolimerization was performed in the presence of microseminoprotein-beta (MSMB) creating target protein specific cavities on the surface of a screen-printed carbon. Dopamine was introduced as charged monomer labelling the binding site and was allowed to self-organize around the protein. The subsequent electropolimerization was made by applying a constant potential of +2.0 V, for 30 s, on a carbon screen-printed electrode, immersed in a solution of protein and CAF prepared in phosphate buffer. The sensor with charged monomers showed a more sensitive response, with an average slope of−7.59 A/decade, linear concentration range of 0.5–100 ng/mL and a detection limit of 0.12 ng/mL. The corresponding non-imprinted sensor displayed an inconsistent response over the range of the calibration curve. The biosensor was successfully applied to the analysis of MSMB in serum and urine samples.
- Sarcosine oxidase composite screen-printed electrode for sarcosine determination in biological samplesPublication . Rebelo, Tânia S. C. R.; Pereira, Carlos M.; Sales, M. Goreti F.; Noronha, João P.; Costa-Rodrigues, João; Silva, Fernando; Fernandes, M. H.Prostate Cancer (PCa) is the most common form of cancer in men in Europe with a 61.4 % incidence among all cancer cases and a 12.1 % mortality [1] and, therefore, its early detection is fundamental for increasing the survival rate. Currently, diagnosis and management of patients with PCa is only based on the determination of the biomarker Prostate Specific Antigen (PSA). However, the method used for PCa detection has poor sensitivity and specificity, leading to false negative and false positive test results and many patients are sent to unnecessary biopsy procedures [2]. Therefore, there is a need to seek for new biomarkers and more effective screening. In this work, a biosensor device was developed for the quantification of sarcosine via electrochemical detection of H2O2 (at 0.6 V) generated from the catalyzed oxidation of sarcosine. The detection was carried out after the modification of carbon screen printed electrodes (SPEs) by immobilization of sarcosine oxidase (SOX) on the electrode surface. The strategies used herein included the activation of the carbon films by an electrochemical step and the formation of an NHS/EDAC layer to bond the enzyme to the electrode, the use of metallic or semiconductor nanoparticles layer previously or during the enzyme immobilization. In order to improve the sensor stability and selectivity a polymeric layer with extra enzyme content was further added. The proposed methodology for the detection of sarcosine allowed obtaining a limit of detection (LOD) of 1.6x10-5 mM, using a linear concentration range between 1x10-5 and 1x10-4 mM. The biosensor was successfully applied to the analysis of sarcosine in urine samples.
- Sarcosine oxidase composite screen-printed electrode for sarcosine determination in biological samplesPublication . Rebelo, Tânia S. C. R.; Pereira, Carlos M.; Sales, M. Goreti F.; Noronha, João P. C.; Costa-Rodrigues, João; Silva, Fernando; Fernandes, M.H.As the prostate cancer (PCa) progresses, sarcosine levels increase both in tumor cells and urine samples, suggesting that this metabolite measurements can help in the creation of non-invasive diagnostic methods for this disease. In this work, a biosensor device was developed for the quantification of sarcosine via electrochemical detection of H2O2 (at 0.6 V) generated from the catalyzed oxidation of sarcosine. The detection was carried out after the modification of carbon screen printed electrodes (SPEs) by immobilization of sarcosine oxidase (SOX) on the electrode surface. The strategies used herein included the activation of the carbon films by an electrochemical step and the formation of an NHS/EDAC layer to bond the enzyme to the electrode, the use of metallic or semiconductor nanoparticles layer previously or during the enzyme immobilization. In order to improve the sensor stability and selectivity a polymeric layer with extra enzyme content was further added. The proposed methodology for the detection of sarcosine allowed obtaining a limit of detection (LOD) of 16 nM, using a linear concentration range between 10 and 100 nM. The biosensor was successfully applied to the analysis of sarcosine in urine samples.