Novel Architectures For Improved thin film Solar Sells (NAFISC)

Funder

Organizational Unit

Publications

Cu(In,Ga)Se2 based ultrathin solar cells: the pathway from lab rigid to large scale flexible technology

Publication . Lopes, Tomás; Teixeira, Jennifer; Curado, Marco; Ferreira, Bernado; Oliveira, Antonio; Cunha, José; Monteiro, Margarida; Violas, André; Barbosa, João; Sousa, Patricia; Çaha, Ihsan; Borme, Jérôme; Oliveira, Kevin; Ring, Johan; Chen, Wei; Zhou, Ye; Takei, Klara; Niemi, Esko; Francis, Leonard; Edoff, Marika; Brammertz, Guy; Fernandes, Paulo; Vermang, Bart; Salomé, Pedro

For the first time, the incorporation of interface passivation structures in ultrathin Cu(In,Ga)Se2 (CIGS) based solar cells is shown in a flexible lightweight stainless-steel substrate. The fabrication was based on an industry scalable lithography technique - nanoimprint lithography (NIL) - for a 15x15 cm2 dielectric layer patterning, needed to reduce optoelectronic losses at the rear interface. The nanopatterning schemes are usually developed by lithographic techniques or by processes with limited scalability and reproducibility (nanoparticle lift-off, spin-coating, etc). However, in this work the dielectric layer is patterned using NIL, a low cost, large area, high resolution, and high throughput technique. To assess the NIL performance, devices with a NIL nanopatterned dielectric layer are benchmarked against electron-beam lithography (EBL) patterning, using rigid substrates. Up to now, EBL is considered the most reliable technique for patterning laboratory samples. The device patterned by NIL shows similar light to power conversion efficiency average values compared to the EBL patterned device - 12.6 % vs 12.3 %, respectively - highlighting the NIL potential for application in the solar cell sector. Moreover, the impact of the lithographic processes, such as different etch by-products, in the rigid solar cells’ figures of merit were evaluated from an elemental point of view via X-ray Photoelectron Spectroscopy and electrically through a Solar Cell Capacitance Simulator (SCAPS) fitting procedure. After an optimised NIL process, the device on stainless-steel achieved an average power conversion efficiency value of 11.7 % - a slightly lower value than the one obtained for the rigid approach, due to additional challenges raised by processing and handling steel substrates, even though scanning transmission electron microscopy did not show any clear evidence of impurity diffusion towards the absorber. Notwithstanding, time-resolved photoluminescence results strongly suggested the presence of additional non-radiative recombination mechanisms in the stainless-steel absorber, which were not detected in the rigid solar cells, and are compatible with elemental diffusion from the substrate. Nevertheless, bending tests on the stainless-steel device demonstrated the mechanical stability of the CIGS-based device up to 500 bending cycles.

2022Journal article

Open access

Will ultrathin CIGS solar cells overtake the champion thin-film cells? Updated SCAPS baseline models reveal main differences between ultrathin and standard CIGS

Publication . Violas, André F.; Oliveira, António J.N.; Teixeira, Jennifer P.; Lopes, Tomás S.; Barbosa, João R.S.; Fernandes, Paulo A.; Salomé, Pedro M.P.

Cu(In,Ga)Se2 (CIGS) solar cells are amongst the best performing thin-film technologies, with the latest performance gains being mainly due to recent years improvements obtained with post-deposition treatments (PDT). Moreover, thinning of the absorber layer down to sub-micrometre values (ultrathin absorbers) is of extreme importance for CIGS to be even more cost-effective and sustainable. However, electrical and optical limitations, such as rear interface recombination and insufficient light absorption, prevent the widespread implementation of ultrathin CIGS devices. The recent electrical CIGS simulation baseline models have failed to keep up with the experimental developments. Here an updated and experimentally based baseline model for electrical simulations in the Solar Cell Capacitor Simulator (SCAPS) software is presented and discussed with the incorporation of the PDT effects and increased optical accuracy with the support from Finite-Difference Time-Domain (FDTD) simulation results. Furthermore, a champion solar cell with an equivalent architecture validates the developed thin-film model. The baseline model is also applied to ultrathin CIGS solar cell devices, validated with the ultrathin champion cell. Ultimately, these ultrathin models pave the way for an ultrathin baseline model. Simulations results reveal that addressing these absorbers' inherent limitations makes it possible to achieve an ultrathin solar cell with at least 21.0% power conversion efficiency, with open-circuit voltage values even higher than the recent thin-film champion cells.

2022Journal article

Open access

Exploiting the Optical Limits of Thin‐Film Solar Cells: A Review on Light Management Strategies in Cu(In,Ga)Se 2

Publication . Oliveira, António J. N.; Teixeira, Jennifer P.; Ramos, Duarte; Fernandes, P. A.; Salomé, Pedro M. P.

Light management strategies are of utmost importance to allow Cu(In,Ga)Se2 (CIGS) technology market expansion, as it would enable a conversion efficiency boost as well as thinner absorber layers, increasing sustainability and reducing production costs. However, fabrication and architecture constraints hamper the direct transfer of light management architectures from other photovoltaic technologies. The demand for light management in thin and ultrathin CIGS cells is analyzed by a critical description of the optical loss mechanisms in these devices. Three main pathways to tackle the optical losses are identified: front light management architectures that assist for an omnidirectional low reflection; rear architectures that enable an enhanced optical path length; and unconventional spectral conversion strategies for full spectral harvesting. An outlook over the challenges and developments of light management architectures is performed, establishing a research roadmap for future works in light management for CIGS technology. Following the extensive review, it is expected that combining antireflection, light trapping, and conversion mechanisms, a 27% CIGS solar cell can be achieved.

2022Journal article

Open access